Concurrent Technologies VP 110/010-E or -K

	v. 4.0 (hardware-vendor BSP), 3.10a (hardware-vendor BSP)
Architecture:	x86
Processor group:	Pentium III
Markets:	telecommunications, industrial, medical, military and aerospace
Please consult the board-support guide or contact us for specific platform features supported.

The VP 110/010-E and VP 110/010-K are PC-compatible, high-performance, high-functionality VME processor boards. Each supports the 800MHz low-voltage Intel Pentium® III processor 512K. This single-slot board features two PMC sites, up to 1 Gbyte of synchronous DRAM and a variety of interfaces, including an option for an on-board hard disk drive, CompactFlash™ drive. Both boards are suitable for a range of demanding applications within the industrial control, telecom, telemetry, scientific and aerospace markets.

Operation over ambient temperature range

• -E: -25°C to +70°C
• -K: -40°C to +85°C

Central processor

• low-power Pentium III processor operating at 800MHz
  • using a flip-chip CPU
  • 32 Kbytes internal (Level 1) on-die cache
  • 512 Kbytes of secondary (Level 2) on-die cache
  • no CPU fan; low-power processor
• utilizes 64-bit ServerWorks' ServerSet™ III LE chipset: supports 133MHz bus frequency
• Pentium III (ITP) debug port

DRAM

• supporting up to 1 Gbyte of 133MHz ECC SDRAM
  • 512 Mbytes soldered on the board
  • up to 512 Mbytes provided via a SODIMM socket
  • single bit error correction; double-bit error detection
• accessible from Pentium III processor or VME bus

EIDE hard disk interfaces

• accessed via P2 connector
• supports up to Ultra-DMA 100 for high performance drives
• two channels (primary and secondary)
• primary channel is accessible via P2 connector
• secondary channel can be used for on-board CompactFlash carrier

Ethernet interface

• 2 x 10Base-T and 100Base-Tx channels for UTP CAT-5
• implemented by two 82559ER LAN controllers
• accessed via two RJ45 front panel connectors
• programmable station ID

PMC (PCI mezzanine card) interface

• 2 x PMC sites and for both sites
  • I/O via front panel, also via P2 for site 1 and optionally via P0 for site 2
  • 32/64-bit operation
  • 33/66MHz PCI operation
• expansion connector to an optional PMC carrier board for two additional PMC sites

Serial interface

• 1 x RS232 serial channel
• 16550 compatible UART
• accessed via an RJ45 connector on the front panel

Battery-backed SRAM

• 512 Kbytes of battery-backed low-power SRAM

Flash EPROM

• 64 Mbytes Application Flash EPROM
• 512 Kbytes of BIOS Flash EPROM

Firmware support

• PhoenixPICO™ BIOS
• comprehensive Power-On Self-Test (POST)

Other peripheral interfaces

• PC-compatible real-time clock (Year 2000 compliant)
• floppy disk interface via P2 connector
• 1x USB (Universal Serial Bus) interface via P2 connector
• Watchdog timer
• 1 x 32-bit long-duration timer with processor interrupt capability
• keyboard interface via 4-pin header
• mouse interface via 4-pin header

VME interface

• implemented using Tundra® Universe II™ device
• VME Master/Slave
• A32/A24/A16/D64/D32/D16/D8(EO)/MBLT64
• fast hardware byte swapping
• auto system controller detect
• full interrupter / interrupt handler support
• bus error interrupt hardware

Electrical specification

• +5V@6A (typical with 1 Gbyte DRAM)
• +12V@0.0A; -12V@0.0A
• +12V and -12V routed to both PMC sites and PMC expansion connector

Environmental specification

• E version:
  • -25°C to +70°C (operating)
  • 10% to 90% relative humidity, non condensing (operating)
  • -40°C to +70°C (storage)
  • 10% to 90% relative humidity, non condensing (storage)
• K version:
  • -40°C to +85°C (operating)
  • 0% to 100% relative humidity, non condensing (operating)
  • -40°C to +85°C (storage)
  • 0% to 100% relative humidity, non condensing (storage)
  • humidity-sealed
• for commercial temperature version, see VP 110/01x VME board

Mechanical specification

• 6U form-factor
• single VME slot—front panel width 0.8inch (20.3mm)
• utilizes a 160-way DIN connector for P1 and P2
  • compatible with normal 96-way DIN connectors
• optional P0 (optional for VME64x backplanes only)
• shock:
  • 20g, 11ms, ½ sine (operating)
  • 30g, 11ms, ½ sine (non-operating)
• vibration:
  • 5Hz-2000Hz at 2g, 0.38mm peak displacement (operating)
  • 5Hz-2000Hz at 5g, 0.76mm peak displacement (non-operating)

View more Concurrent boards, or learn more about Concurrent Technologies—a SynergyWorks partner.